Re: EX-2200-c restart interfaces every few seconds
Hi Folks,Please configure syslog file messages with "any any"and share "show log messages" from the box.
View ArticleRe: EX4200 OSPF not working properly
AshvinO Still having issues, with this not picking the ge- interfaces for all 0.0.0/0 traffic. admin@CORPSW01# show protocols ospf traceoptions { file OSPF_Troubleshooting; inactive: flag error;...
View ArticleRe: vqfx10k-pfe is not starting
Hi,I have tried to add console=ttyS0 and after that do ctrl-x to boot the image.Unfortunately no more debugs occur. //Niklas
View ArticleRe: vqfx10k-pfe is not starting
i still think it could be console related as you should be getting some ouput. however, you do not need access via console. the pfe should connect automatic to the RE via the 169.254.0 network on...
View ArticleRe: vqfx10k-pfe is not starting
Hi,Is work now. The pfe image did start, it was only a display issue as you said.The other thing was the bridge between re and pfe. Thanks for the supoort
View Articlearp inspection fails on specific vlan
Experts, ge-0/0/6 24 0 24 where 24 is of ARP inspection failed, ge-0/0/6:description "Voice&Data";unit 0 { family ethernet-switching {...
View ArticleRe: Juniper switchport configuration
Perhaps the POE usage is over the power supply capacity http://www.juniper.net/documentation/en_US/release-independent/junos/topics/reference/specifications/power-ex4200-electrical.html POE status...
View ArticleRe: Juniper switchport configuration
I have been doing a LOT of work with POE on Juniper products, more specificlly with EX4200, and then soon with EX4300, and I have never seen a port 'flap' in association with POE. I'd highly suggest...
View ArticleRe: QFX/EX
You can request a free download of the vQFX here. https://www.juniper.net/us/en/dm/free-vqfx-trial/ This blog describes setting it up on...
View ArticleEx4600 switch route import using rib-groups but still not able to ping
Iam trying to ping the loopback address of the EX-4600 switch where loopback is the only interface in master routing instance and iam using rib-groups to populate the static route pointing towards my...
View ArticleClik here to view.
Traceroute working but not able to ping the loopback of the switch
Below is the simple topology iam working on. The direct link between cisco router and the switch is in the separate v1-VRF. I have added loopback interface configurations in the Switch which is in the...
View ArticleRe: Ex4600 switch route import using rib-groups but still not able to ping
Looks like the root routing instance does not have the interface route 10.10.59.80/30 which would be needed for the reply. Try adding the interface routes set routing-options interface-routes rib-group...
View ArticleRe: Ex4600 switch route import using rib-groups but still not able to ping
Still not able to ping the loopback from host.Iam not able to ping the 10.10.59.81 (next hop) from the switch master routing table, it all works fine from V1-VRF, I tried to put the loopback in the...
View ArticleRe: Ex4600 switch route import using rib-groups but still not able to ping
What is the host address you are doing the ping from as 10.10.59.81 is the interface address on the cisco?Does ping fail in both directions from Junipter to host and from host to Juniper? What does...
View Articlesecure specific port
Experts, can I secure specific port for example access port where a computer is pluged? So next time somebody unplugged and plug different device the port will go down ...... would be nice to have log...
View ArticlePVLANs with Secondary VLAN Trunk Ports on ex4600
Hi I have a few stacks of ex3400 switches setup with PVLAN. On each stack the uplink port goes into a single ex4600 unit as aggregation. I wish my ex4600 to treat traffic from the ex3400 stacks as...
View ArticleRe: Ex4600 switch route import using rib-groups but still not able to ping
Host address is 10.10.67.20yes, ping fails from both direction no responses from any hops on trceroute from switch to hosttraceroute from host to switch tracert 10.10.59.2461 * * * Request...
View ArticleRe: secure specific port
I have found: edit ethernet-switching-options secure-access-portset interface ge-* mac-limit 1 action dropset interface ge-* allowed-mac <MAC> So if sometinging is going on I would have message...
View ArticleRe: Ex4600 switch route import using rib-groups but still not able to ping
Based on this data it looks like 10.10.67.20 should hit your default route in the route routing instance. Can you confirm that with: show route 10.10.67.20 Also can you ping and trace route to the...
View ArticleRe: Ex4600 switch route import using rib-groups but still not able to ping
I found exact symptoms i have in one of the KB which had a workaround to use filter base forwarding using firewalls to forward the packets to desired routing instance. I added the input filter to...
View Article