Re: IPv6 on vme
It doesn't matter which release. This is not supported.=====If this worked for you please flag my post as an "Accepted Solution" so others can benefit. A kudo would be cool if you think I earned it.
View ArticleRe: Q-in-Q QFX 5100
Yes, this is correct, L2PT is not supported at this moment on QFX5100/EX4600.=====If this worked for you please flag my post as an "Accepted Solution" so others can benefit. A kudo would be cool if you...
View ArticleEX4600 on ELS: l3-interface over a QinQ / C-VLAN
Hello, After reading various posts in the forum and using Juniper's documentation, we managed to have a working QinQ configuration for our EXs: We can switch packets from a dot1Q trunk to a QinQ....
View ArticleHow do I set the config on a new member vc
I have a new EX4500 that I want to add to the existing VC.So, my question is, do I need the config to be a basic config.? Or will the VC populate this new EX4500 with the correct config, once I add it...
View ArticleRe: Web Management not functiong ES-4200 11.4R7.5
and if the solution provided in the KB didn't solve your problem , then as mentioned in the KB you'll need to open JTAC case . But you cannot do that when you're running 11.4 version as this version is...
View ArticleRe: Juniper compatibility with Cisco vCP
Thanks for the response.It looks like MC-LAG and vCP are both implementations of the IEEE 802.1AX-2008 standard.I can not fine anywhere that says they are compatible. In fact I find that each is a...
View ArticleRe: Juniper compatibility with Cisco vCP
Look for this cookbook and search for MC-LAGhttp://networktest.com/jnpriop/cookbook.pdfI am going to try and attach it
View ArticleIs there an Industrial L2 Switch from Juniper?
Hi allIs there an Industrial L2 Switch from Juniper/or IP65 Switch for outdoor?Thanks
View ArticleRe: Is there an Industrial L2 Switch from Juniper?
HI Amal, Juniper does not have an industrial L2 switch or outdoor switches. A few alternative options: * Look at the ACX1100 which is temperature hardened without fans but requires an outdoor rack....
View ArticleMaster became a linecard
Good day everybody. I have 2 sw ex4200 in virtual chassis/ I know about no-split-detectionBut the point is: When Master fails - Backup becames Master within 1-2 seconds.But if I reboot new Master (...
View ArticleRe: Master became a linecard
HI Please disable this config set virtual-chassis no-split-detection This was introduced to avoid split brain. Without this config you should not go into linecard mode. If it goes also just try the...
View ArticleRe: EX4600 on ELS: l3-interface over a QinQ / C-VLAN
HI Are you talking about a scenario where PC / host is directly attached to PE? Example of such is QinQ with PC directly connected to PE Devices. +---------------+ +-----------------+...
View ArticleRe: Q-in-Q QFX 5100
Hope this helps. QinQ ELS Configs+------------------+ +------------------+ +--------------------+ +--------------------+| EX2200 +---------+ QFX-5100...
View ArticleRe: Master became a linecard
Hold on.Did you mean I shoud enable splin-deteciton ?It's bad scenario for me. Because if I enable splin-deteciton and Master switch fail - backup switch became a linecard at this mometn and I loss...
View ArticleRe: EX4600 on ELS: l3-interface over a QinQ / C-VLAN
Hello Partha, Many thanks for your answer; it does describe a QinQ configuration for transport, as this other post did show: https://forums.juniper.net/t5/Ethernet-Switching/Q-in-Q-QFX-5100/m-p/307779....
View ArticlePvlan irb ipv6 on QFX5100
Hi, I have bought QFX5100 to my datacenter. I would like configure private vlan domain with about 200 community vlans(one community vlan per customer)On this qfx there would be L3 interface - irb with...
View ArticleRe: Pvlan irb ipv6 on QFX5100
Do you know, anything similar to unrestricted proxy arp on ipv6?
View ArticleHyper-V DUP! Ping
Hello, We recently cahnged our cisco sf300 switch with juniper ex2300. It is great but we have one problem.The switch is in default configuration only vlans are configured. The Hyper-V host is...
View ArticleEvaluation Upgrade EX2300-C to EX2300 or EX3400 or EX4300
Hello, I'm in charge of a branch where currently only an EX2300-C POE switch is deployed.Besides that there's only a gateway and no aggregation devices. From what I understand, EX2300-C only supports...
View Article