Re: OID for SNMP monitoring line cards in EX9204
Hi Krishna_85, What Junos image do you have on the device? (You can use command"show version" to check)What all specifics do you want monitor for line cards in EX9204? //NEX
View ArticleLog message meaning, EX4500-40f "Power not OK on uplink in pic_slot = 3"
Hi fellow network enthusiasts, I am seeing these logs flooding my EX4500-40f, can you please help me understand what these logs mean in detail: Jun 1 09:45:05 xx: %DAEMON-3: Power not OK on uplink in...
View ArticleRe: vQFX 18.1R1.9 PFE.
Hi,Is anybody was able to fine the Release notes about this version or previous one 17. Which features are supported, what still not and etc. Thanks!
View ArticleRe: no fiber connectivity
cc18, Thank you for sharing all that you are trying, I am intrigued to see what it turns out to be!Let me know of your findings on this. Thanks! //Nexon
View ArticleFirewall filter types
What is the difference between port, VLAN and RVI filters? Of course, they are applied differently in the configuration, but is it all, that there is? Regards,Pawel Mazurkiewicz
View ArticleEX2300 not completing ZTP process
Hello all,I have a working Cent OS server that is giving out dhcp and is also acting as a ftp server. ZTP works as it should on EX-2200 switches but something is off when I try to perform the same...
View ArticleVACL and RVI
Does an ingress vlan filtrer (VACL) apply to traffic entering the vlan from its (internal) rviinterface? I.e. to traffic routed from another vlan?Similarly, does an egress vlan filter apply to traffic...
View ArticleRe: vQFX 18.1R1.9 PFE.
Hi Sergeiu. I haven't found the realease notes for vQFX10K versions 17.4R1 or 18.1R1. That was one of my questions to Juniper SE as well (1. PFE image being RE image, 2. interface em4 on RE (light...
View ArticleRe: LAG port goes BLK DIS state after adding to VSTP
OK that make sense.I was in data center today to physically connect the cable. And guess what. Connection just don't come up at all (port LEDs are dead on both ends), what is interesting I tried a...
View ArticleRe: LAG port goes BLK DIS state after adding to VSTP
Hello, wrote:Hi, What I do wrong ? Likely Your AE count is too low.Please post the following:show configuration chassis aggregated-devices | display setHTHThxAlex
View ArticleRe: Breaking apart a EX4600 and EX4300 mixed mode chassis
Thank you for this,Follow up question though:I still want to break apart my EX4600s and EX4300s. I'm essentially trying to make the EX4600 act as an MDF and create a new IDF with the EX4300 stack....
View ArticleRe: LAG port goes BLK DIS state after adding to VSTP
Without a link nothing else will matter--lacp, ae device-count, or stp. Check the basics and get a link first: optics match, fiber polarity, speed/duplex negotiation.
View ArticleRe: LAG port goes BLK DIS state after adding to VSTP
Alex ae count I have is 20. set chassis aggregated-devices ethernet device-count 20That would be to trivial and too easy to spot.I will try to enable all debugging on ae14 and try again what I wrote...
View ArticleRe: LAG port goes BLK DIS state after adding to VSTP
OK there is one more possible thing. Optics On Juniper QFX VC I use Cisco 1 Gig transceivers. They are detected as: Xcvr 28 NON-JNPR FNS143205E2 SFP-SX Xcvr 29 NON-JNPR FNS14320K5E SFP-SX
View ArticleClik here to view.
Re: LAG port goes BLK DIS state after adding to VSTP
OK today morning I was in DC and I think for 99% it is the problem of optics. I had only in stock a Cisco 1 GB SFP-SX transceiver modules, and the partner from which we bough Junipers told us the Cisco...
View ArticleRe: QFX5200: issu yes or no?
@Nico82, I hope you do see this response, as I know this is old thread. Juniper TAC is designed to handle break/fix situations, not "will it happen" type of questions. In just checking now, the...
View ArticleRe: LLDP_Multicast traffic doesn't flow throgh the EX2200
HelloI'm still suffering with this issue. I configure as simple as i can. why it doesn't work? Configuration:root@XXXXXXX# show ## Last changed: 2015-05-02 12:57:49 CEST version 12.3R9.4; system {...
View ArticleClik here to view.
show wrong vlan with interface range
Hello, For purpose learning. I created a VLAN named CAMERA-VLAN (id 999) and created a interface-range named CAMERA-RANGES belong to CAMERA-VLANinterface-range CAMERA-RANGES {member-range ge-0/0/0 to...
View ArticleRe: show wrong vlan with interface range
I suspect that under interface-range you have CAMERA-VLAN but under each of the interfaces you have ID-VLAN1.More specific configuration wins. You will have to delete configuration specific to each...
View Article