Clik here to view.
Re: User authentication via CIsco ACS
I want to create a DCN network and want to know if any storm occur from server/Lan side in above case then can i login into the switches during the issue via Managment port.note-: currently i am...
View ArticleClik here to view.
Re: Difference between CON and MGMT port on back of EX-4200?
I want to create a DCN network and want to know if any storm occur from server/Lan side in below case then can i login into the switches during the issue via Managment port.note-: currently i am...
View ArticleEX 4200 - Got Tx underrun for Port:1
Hi guys,I have EX 4200 , JUNOS 12.3R10.2, and strange message : Jun 28 16:17:29 ex4200 chassism[1349]: cm_cheetah_ifd_read_port_intr_cause: Got Tx underrun for Port:1Jun 28 16:17:35 ex4200...
View ArticleRe: EX 4200 - Got Tx underrun for Port:1
Hi, I believe it could be due to speed/duplex mismatch on the interface:"Interface has a TX buffer for outgoing traffic, when the rate of traffic pushed to this buffer is too high the interface cannot...
View ArticleRe: EX 4200 - Got Tx underrun for Port:1
Hi AshvinO,unfortunately this dosn't helo. EX4200 is connected to MX10. I try this: EX4200: ether-options { no-flow-control; link-mode full-duplex; speed { 10g; } }MX10[edit interfaces xe-1/2/0]...
View ArticleRe: EX 4200 - Got Tx underrun for Port:1
Hi, Can you check the speed / duplex state of interfaces on each side:show interfaces x/x/x extensiveCheers,Ashvin
View ArticleRe: Difference between CON and MGMT port on back of EX-4200?
It's hard to give a complete answer without more detail. If the switch is experiencing a broadcast storm it's likely that routing processes and other control plane functions will fail because of high...
View ArticleRe: QFX5100 not getting a dhcp address on the mgmt interface
thanks for the info, i tried those but still am not getting a dhcp address
View ArticleRe: QFX5100 not getting a dhcp address on the mgmt interface
I think the 'new way' is to use dhcp-client keyword instead of dhcp. Also make sure you're plugged into port C0 and not CON...
View ArticleRe: EX 4200 - Got Tx underrun for Port:1
Output of commands , are with default configuration of speed , duplex, flow-control etc ...EX 4200Physical interface: xe-0/1/2, Enabled, Physical link is Up Interface index: 166, SNMP ifIndex: 553,...
View ArticleRe: EX 4200 - Got Tx underrun for Port:1
Hi, Just wandering whether the input errors are incrementing?
View ArticleRe: QFX5100 not getting a dhcp address on the mgmt interface
QFX5100-48S has em0 and em1 as mgmt interface. but the actual IP is assigned on vme unit 0 cause its a virtual mgmt interface and I don't know why documentation from juniper doesn't mention this. There...
View ArticleSNMP check for queue data rate
On my SRX devices, I'm successfully monitoring CoS queue data rates using the jnxCosQstatTxedByteRate OID, but a query on EX devices always returns a rate of zero, even though the xmit byte count is...
View ArticleRe: Voice VLAN
If no valid data device is being attached, which is what your description sounds like, why not just create a VLAN on the switch that doesn't go anywhere and assign it to the ports to be protected?
View ArticleRe: Voice VLAN
It's already has a VLAN of its own . This VLAN needed to reach multiple servers on LAN , not just the CUCM server .. Thats why we raised solution #1 .. ACL on the L3 BB switch and policy on fw + port...
View ArticleRe: SNMP check for queue data rate
well , im not sure , but just found this document https://forums.juniper.net/jnet/attachments/jnet/switch/1676/1/Key%20Performance%20Indicators%20for%20Juniper%20Devices%20version%202%202.pdfits about...
View ArticleRe: QFX5100 not getting a dhcp address on the mgmt interface
OOB management ports in standalone and virtual chassis , is different .'me' interface is when standalone switch is used 'vme' interface is when virtual-chassis switches is used
View ArticleRe: QFX5100 not getting a dhcp address on the mgmt interface
http://www.juniper.net/documentation/en_US/junos15.1/topics/task/configuration/virtual-chassis-qfx-series-cli.htmlstep 5
View ArticleRe: Storm-Control: Logging Instances of bandwidth limit being hit
Dear aloeffle, We have configured the below policy still not receving the SNMP trap to NMS system. Can you please help to resolve this. show configuration event-options policy STORM_CTLevents...
View ArticleRe: Difference between CON and MGMT port on back of EX-4200?
Thanks for your reply. if storm occur from any port then switch CPU will be very high and in that situtation will i able to login from DCN router using management subnet or not.
View Article