Re: Set a trunk port with access VLAN issue
Please, show EX config of interface in trunk mode.Which linux are you using?
View ArticleRe: Ex4300 Virtual Chassis member issue
Hi,Please try this command , and update me if the issue still exist :set system processes ethernet-connectivity-fault-management disable
View ArticleRe: Set a trunk port with access VLAN issue
We try with centos and debian an we have the same result. The junuper configuration is: ge-0/0/10 {description Pruebas;unit 0 {family ethernet-switching {port-mode trunk;vlan {members [ Telefonia...
View ArticleRe: EX2200-C POE+
A whole bunch of problems with APs that supported PoE+ are problems with PoE negotiation. Make sure that LLDP runs. In some cases you could solve an issue by manual setting up power value for...
View ArticleRe: Set a trunk port with access VLAN issue
You don't needed to place the untagged vlan to vlan members list.remove it:delete interface ge-0/0/10 unit 0 family ethernet-switching vlan members Telefonia
View ArticleRe: Set a trunk port with access VLAN issue
That's working configuration from my servers (Centos):/etc/sysconfig/network-scripts/ifcfg-eth1.333VLAN=yes DEVICE=eth1.333 PHYSDEV=eth1 TYPE=Ethernet BOOTPROTO=static ONBOOT=yes IPADDR=10.200.0.2...
View ArticleRe: Ex4300 Virtual Chassis member issue
Thank you Abed AL-R Unfortunately, the same issue exists after entering"set system processes ethernet-connectivity-fault-management disable" I also did the same process of failover as before.
View ArticleBlocking/Filtering BPDUs
Using an ex4300 and ELS style config, I have configured interface ranges, say access-vlan4, and I have configured RSTP on that range: rstp { interface access-vlan4 { edge; } bpdu-block-on-edge;} also...
View ArticleRe: Set a trunk port with access VLAN issue
OK I will try removing the untagged VLAN form the list and let you know In your configuration you have the VLAN 333 as tagged and 3004 as untagged is that correct ?
View ArticleRe: Ex4300 Virtual Chassis member issue
Hi,Does The server receive IP address after the failover ?Apparently , this issue isn't as I expected it . There might be a little chance that it is version related but I'm not sure .I recognized some...
View ArticleClik here to view.
Re: Juniper EX 4600 and 4300 Virtual Chassis
Thanks for the help, i kinda know why the interfaces don't work.It's because the VC is not supported using just one EX4600 and all the other members EX4300In case of failure of the master (ex4600) only...
View ArticleRe: Ex4300 Virtual Chassis member issue
Hi Abed AL-R, The server is on static IP. The server is pinging the router and when I reboot FPC1, the ping is continuous. But when I reboot FPC0, the ping connection fails and only comes back after...
View ArticleRe: EX2200-C POE+
Please get output for show poe interface <interface-name> where this is the Interface the Meru AP is plugged into. You can also try and set the following to see if you get better results: set...
View ArticleRe: Set a trunk port with access VLAN issue
Sorry to me it makes no sense that one server type works and others do not. I would not expect and config change to make this all work. I suggest monitor traffic at the interface and capture packets...
View ArticleClik here to view.
Re: Blocking/Filtering BPDUs
Hmmm... By simple words: "I want to filter BPDUs, but I don't want to filter BPDUs" Very interesting question, but need the purpose of your tasks: why do you need to discard incoming BPDUs?
View ArticleRe: Juniper EX 4600 and 4300 Virtual Chassis
Good to hear that , would help any one trying the same, I never noticed it , since I had two 4600 + two 4300. Binoy
View Articleex3300 and Voip
Hello experts,I am at a site and the core routers are passing all vlan to ex3300 switch, with avaya phones being used.Data and voip had been configured on the ex3300 port, but I can only see the data...
View Article