Re: BGP L2VPN Question - Site-ID and Remote-Site-ID
Can you try this at both ends [edit interfaces]ge-0/0/1 {vlan-tagging;encapsulation extended-vlan-ccc;unit 0 {vlan-id-list [192 193];} instance-type l2vpn;interface ge-0/0/1.0;protocols {l2vpn...
View ArticleRe: EX2200 loader> can't load '/kernel'
Yes, I have triedUnfortunatelly it didn't gives more info about the error: cannot open package (error 22)
View ArticleRe: EX2200 loader> can't load '/kernel'
Hi, Could you possibly try this:https://kb.juniper.net/InfoCenter/index?page=content&id=KB29113&actp=RSS Cheers,Ashvin
View ArticleRe: EX2200 loader> can't load '/kernel'
Already trie. It says kernel not found (obviously because in order to boot up it needs for the kernel but the kernel...................can't be load)
View ArticleClik here to view.
Re: EX3300 - out-of-band interface - not working
Hi guys, thank you for help but I can not delete interface vme. root@xxx# delete interfaces vmewarning: statement not found if I write "delete interfaces ?" I can`t see vme interface in the list......
View ArticleRe: EX3300 - out-of-band interface - not working
Please paste the entire config in here, then it's easier for us to guide you. On a side note I would recommend you to look at the Day One library which is a collection of pdf's which gives a very good...
View ArticleRe: EX2200 loader> can't load '/kernel'
Hi, Yes of course. I guess in that case RMA. Cheers,Ashvin
View ArticleRe: EX3300 - out-of-band interface - not working
Hi, I`ve pasted whole config to .txt file in attachments. Thanks,Stefan
View ArticleRe: EX3300 - out-of-band interface - not working
Hi, One of the things you could do is view configuration in display set mode and then replace set with delete. show configuration | display set vme would be something like:set interfaces vme unit 0...
View ArticleRe: EX2200 loader> can't load '/kernel'
Remember that EX2200, EX3200 and EX3300 has limited lifetime warranty so even without support, you should be able to RMA the switch (ref. https://www.juniper.net/support/warranty/990235.pdf)
View ArticleClik here to view.
Re: EX3300 - out-of-band interface - not working
Hi, - I am connected via CLI via IP 172.16.20.254- I attached whole output of display set (this is really useful) set interfaces me0 unit 0 family inet set interfaces vlan unit 0 family inet address...
View ArticleRe: EX3300 - out-of-band interface - not working
first try... root@xxx# delete interfaces vlan unit 1 family inet address 192.168.200.254/24warning: statement not foundroot@xxx# delete interfaces vme unit 0 family inet address...
View ArticleRe: EX3300 - out-of-band interface - not working
Hi, Can you check for:> show configuration | compareIs there any other configuration changes pending commit? The backup-router allows for a MGMT default route to come up when the rpd [routing]...
View ArticleRe: EX3300 - out-of-band interface - not working
here it is... root@xxx> show configuration | compare {master:0} root@xxx> I don`t know about any other changes pending to commit... I found out that we have "product warranty" till january...
View ArticleRe: EX3300 - out-of-band interface - not working
Hi, Sorry my bad. Should have asked you to do a "show | compare" when in config/edit mode.#show | compareCheers,Ashvin
View ArticleRe: EX3300 - out-of-band interface - not working
there you go... root@MDXKESW06# show | compare [edit interfaces] - me0 { - unit 0 { - family inet; - } - } [edit interfaces vlan unit 0 family inet] address 172.16.20.254/24 { ... } + address...
View ArticleRe: EX3300 - out-of-band interface - not working
"show | compare" gives you a diff of pending changes which will be activated during commit what I will suggest to do is stated below. This rolls the configuration back to the starting point, delete...
View ArticleRe: EX3300 - out-of-band interface - not working
Hi, warning: statement not foundwas because there were pending changes, and the same delete statement was applied again.I am not sure if all those are changes that you intend to commit. If not, you...
View ArticleRe: EX3300 - out-of-band interface - not working
Hi, I will go for rollback and then start again from the scratch, as my shift is over for today I will continue on tomorrow and let you know the results. Thank you cheers,Stefan
View Article