Re: QFX5100 14.1X53-D35 IGMP Leave group message management in the switch
Hi, It seems this behavior is because of the immediate-leave configured on the switch near the headend."When using IGMPv2 snooping, use immediate-leave processing only on VLANs where just one host is...
View ArticleCan't create voice port - config
Dear Experts, I am new to Juniper and switched from Cisco. Here is simple situation: i am in configuration mode and already have port ge-2/0/15 as ether switch and assigned to vlan 20 - I am trying...
View ArticleRe: Can't create voice port - config
Hi, I believe the command would be:set ethernet-switching-options voip interface ge-2/0/15.0 vlan "vlan-name"For vlan member, the vlan name should be specified instead of the vlan-id [compared to...
View ArticleRe: Can't create voice port - config
Hi LOGTECH, IN your case you can just issue the following command to delete all configurations on an interface ( i.e. reset it ) : delete interfaces ge-2/0/15
View ArticleClik here to view.
Re: Firewall filter to restrict traffic for one interface
jonashauge wrote:I think you miss "then accept" in the term: jh@switch# show firewall family ethernet-switching filter test { term test { from { source-address { 192.168.1.66/32; } } then accept; }...
View ArticleRe: Firewall filter to restrict traffic for one interface
ge-0/0/5 is the NAS. I have tried using both input (set from source-address 192.168.1.66/32) and output filters (set from destination-address 192.168.1.66/32). Whenever one of those filters is applied...
View ArticleRe: Firewall filter to restrict traffic for one interface
Hi, I meant either Option 1 or Option 2, i.eOption 1: firewall { family ethernet-switching { filter NAS-Filter-out { term NAS-Filter-Allow { from { source-address { 192.168.1.66/32; } } then { accept;...
View ArticleRe: error: failed to copy file '//var/etc/stp_context.id' to 'fpc1'
Hi,I opened TAC case and then tac suggest me to reimage fpc1 with same junos version. I tried but i am failed but the error shown pointed me to fpc0. while upgrading error was as below:root@core1>...
View ArticleRe: Firewall filter to restrict traffic for one interface
I meant that I have already tried both Option 1 and Option 2 separately. Whenever one of those filters is applied to ge-0/0/5, all traffic to through ge-/0/05 stops. AshvinO wrote:Hi, I meant either...
View ArticleRe: Can't create voice port - config
Hi, Could you check this command:set switch-options voip interface ge-3/0/4.0 vlan "v80-voice"Cheers,Ashvin
View ArticleRe: Can't create voice port - config
looks like switch-option works at least I can type it and no sytax error, but now: set interfaces ge-2/0/15 unit 0 family ethernet-switchingset interfaces ge-2/0/15 unit 0 family ethernet-switching...
View ArticleRe: Firewall filter to restrict traffic for one interface
I added a counter to the firewall filter like so: filter NAS-Inbound { term NAS-Inbound-Allow { from { source-address { 192.168.1.66/32; } } then { accept; count NAS-Inbound-Allowed; } } } I added the...
View ArticleRe: Can't create voice port - config
finally it works: set interfaces ge-2/0/15 unit 0 family ethernet-switchingset interfaces ge-2/0/15 unit 0 family ethernet-switching vlan members "v20-2nd-floor"edit switch-optionsset voip interface...
View ArticleRe: strange behavior EX4200 (unicast flood)
"The dst mac addr may not be in the list in the filter:78:fe:3d:32:1e:c3/48;78:fe:3d:32:1e:db/48;78:fe:3d:32:1e:dd/48;I would suggest trying to identify the traffic src/dst IP & mac addresses and...
View ArticleRe: Can't create voice port - config
Hi, switch-options work because EX4300s use Enhance L2 software [ELS]http://www.juniper.net/techpubs/en_US/junos13.2/topics/task/configuration/getting-started-els.html The commands should be as per...
View ArticleRe: Can't create voice port - config
Yes that worked. Thank You so much for Your help and explanation.
View ArticleRe: Firewall filter to restrict traffic for one interface
Hi,The filter with match condition source-address 192.168.1.66 should be applied as output filter for it to work. Please check Option 1.You could try using match address 192.168.1.66/32 to avoid...
View ArticleRouter-on-a stick Cisco Router with Juniper Switch
I am having trouble getting IP connectivity between two Cisco ASR routers connected to a pair of Juniper EX4500-40f switches in a virtual-chassis setup. The Juniper switch is the new element here, as a...
View ArticleRe: Router-on-a stick Cisco Router with Juniper Switch
Hi, Do you see any mac-addresses on the switch or arp on both sidesshow ethernet-switching table [vlan VLAN100]show arpAlso with a ping running from ASR1 to 10.10.100.3, do you see any traffic on...
View ArticleRe: strange behavior EX4200 (unicast flood)
Hi, spanning-tree indicates recent topology changes.For the unknown unicast traffic to storm flood, there might be a loop causing the storm.Could you check:show spanning-tree interfaceand look whether...
View Article