Re: Adding a EX2300-C POE+ switch to a Pair of EX3300 Switches in a Virtual...
Send the output of show vlans extensive. Cut and paste into text file, and attach the file.
View ArticleRe: Adding a EX2300-C POE+ switch to a Pair of EX3300 Switches in a Virtual...
rccpgm wrote:Send the output of show vlans extensive. Cut and paste into text file, and attach the file.Here is the file...
View ArticleRe: Adding a EX2300-C POE+ switch to a Pair of EX3300 Switches in a Virtual...
Based on the file I attached, I see no reference to Vlan 0.. It seems to be working, but I am still confused why Vlan 0 is tied to ae1 and ae2. Once again, I am wondering if the ports used in the...
View ArticleRe: Adding a EX2300-C POE+ switch to a Pair of EX3300 Switches in a Virtual...
I am going to assume your AE's 1 and 2 are tagged trunks and are set with vlan member all. This is why they are also associated with VLAN 0 - I believe. There will be no harm in having VLAN 0 (which...
View ArticleRe: Alternatives for ring topology - EX3400/EX4600
The answer is to use ERPS (G.8032). This is supported on many EX switches, and I "THINK" it should also be there on EX3400, but I am not 100% sure, and documentation is not clear. This support is...
View ArticleRe: Alternatives for ring topology - EX3400/EX4600
Hi.Thanks for your reply. Well, that was one thought that I had first, to make larger VCs since each can consist of 10 devices we chould group the 7 chassis down to 3 chassis. But we still would have...
View ArticleRe: Alternatives for ring topology - EX3400/EX4600
Hi Johan, you are right in your finding regards EX3400. It does not support ERPS which brings you down to classic xSTP. An option for lowering the impact for a break in the ring could be doing two...
View ArticleRe: Adding a EX2300-C POE+ switch to a Pair of EX3300 Switches in a Virtual...
rccpgm wrote:I am going to assume your AE's 1 and 2 are tagged trunks and are set with vlan member all. This is why they are also associated with VLAN 0 - I believe. There will be no harm in having...
View ArticleQSFP28 DAC cables causing packet loss and framing issues
So the systems I am using are MX960 MPC7e. When I use the 1meter 100G DAC I have zero errors + zero packet loss. When I use the 3meter 100G DAC cables I have packet loss & framing errors. I tried...
View ArticleRemove interface from range
I need to change an interface from a trunk to an access port. Here's the current config: interface-range wireless-ap-ports { member-range ge-4/0/36 to ge-4/0/47; unit 0 { family ethernet-switching {...
View ArticleRe: Remove interface from range
Hi, Basicly you need following lines; delete interface-range wireless-ap-ports member-rangeset interface-range wireless-ap-ports member-range ge-4/0/37 to ge-4/0/47set interfaces ge-4/0/36.0 family...
View ArticleMCLAG Question
Hi there,I have two QFX10K, connected between them with2x40 for ICCP connectivity - ae0 Layer32x100 for ICL connectivity - ae1 as trunkThe MC-AE's interfaces connected to 2 QFX5Kthe iccp is up, the...
View ArticleUplink from EX3300 VC to EX2300-C not passing traffic for Default Vlan (1)
I need your help. Attached are configuration files for the EX3300 and EX2300 switches. I have setup a 20GB uplink from the EX3300 VC to the EX2300 switch using a link aggregation interface. The LACP on...
View ArticleRe: Uplink from EX3300 VC to EX2300-C not passing traffic for Default Vlan (1)
Could it be related to my static route information on the EX2300. On the EX3300, the static route must point to my pfSense router which is 10.1.1.6.
View ArticleRe: Uplink from EX3300 VC to EX2300-C not passing traffic for Default Vlan (1)
I did some more troubleshooting.. Trying to convince myself that this is a routing issue, but not sure. I have setup out-of-band management for the management port on the EX2300. It is assigned an IP...
View ArticleRe: Uplink from EX3300 VC to EX2300-C not passing traffic for Default Vlan (1)
The link aggregation interface on both switches (EX2300 & EX3300) will be carrying tagged traffic on VLAN 30 and untagged traffic from the native Vlan (which is VLAN (1) default). That is my...
View ArticleRe: Uplink from EX3300 VC to EX2300-C not passing traffic for Default Vlan (1)
I am using the EX2300 solely as A Layer 2 switch.
View ArticleRe: Uplink from EX3300 VC to EX2300-C not passing traffic for Default Vlan (1)
I am wondering if I should use a switch port on the EX2300 and not the management port for management of the switch.
View ArticleEX-2300 15.1X53-D56 DHCP snooping untrust on trunk
Hi Guys I seems to have a big problem with configuring trunks as untrusted interfaces. I can not find the way to override a default configuration of DHCP trust on trunk ports. Can you please help....
View ArticleRe: Uplink from EX3300 VC to EX2300-C not passing traffic for Default Vlan (1)
Can someone please help me.
View Article